ACROMAG ACPC8635A

Industry Pack Carrier Cards AcPC8635A CompactPCI Carrier Cards for Industry Pack Modules P5 IP-A FIELD I/O POWER FAILURE LOW VOLTAGE MONITOR AcPC8630A FRONT ACCESS P6 PCI BUS IP-A +5 LBE3# FPGA FIELD J1 I/O -12 PLX INTERRUPT +12 LBE0# PENDING TECHNOLOGY REGISTER RST# PCI9030 INTA# LA(1:9) +5 POWER +5 J2 INTERFACE P2 P1 C/BE(0:3)# INTERRUPT +12 SUPPLY +12 -12 CONTROL -12 FILTERS CHIP IP-A IDSEL REGISTER & FUSES LD(0:15) FIELD IP MODULE A I/O IP A CONTROL FRAME# IP DATA(0:15) & IP ADDRESS(1:6) IRDYi# LINT# AcPC8635A IP MODULE REAR TRDY# ERROR ACCESS STATUS DEVSEL# CS1# +5 POWER +5 J2 P4 P3 +12 SUPPLY +12 AD(0:31) -12 -12 FILTERS IP-B & FUSES LOCK# LRESET# FIELD IP MODULE B I/O IP B CONTROL IP MODULE PERR# LRDYi# ACCESS TIME OUT SERR# CONTROL LR/W# STOP# PAR ADS# CLOCKS CLOCK CONTROL 32 MHz CLOCK 8 MHz Multiply CLOCKS TO Oscillator HIGH SPEED By 4 TRANSCIEVERS IP MODULES Two Industry Pack mezzanine module slots ◆ Non-Intelligent carrier card ◆ CompactPCI bus interface ■ Easy board replacement as I/O needs change. Description Key Features & Benefits The AcPC8635A is a nonintelligent slave ■ Two industry-standard IP module slots ■ Simplified debugging with status LEDs. board that interfaces two IP modules to the ■ Board resides in memory space ■ Quick development of custom I/O boards. CompactPCI® (cPCI) bus. All 100 I/O points are brought out the rear J2 connector. This ■ Supports IP module I/O, ID, INT, and MEM ■ Flexibility to mix and match I/O functions as convenience eliminates messy cables from spaces requirements change. hanging out the front of the cage. In addition ■ Supports 8 and 32 MHz operation to a more efficient cage wiring design, it is also much easier to insert and replace boards. ■ 100 I/O points with rear access ■ High-density rear connectors ■ Compatible with 32-bit CompactPCI® backplane ■ Plug-and-play carrier configuration and interrupt support ■ Two interrupt channels per IP module ■ Front panel LEDs ■ Supervisory circuit for reset generation CompactPCI ■ Individually filtered and fused power to each IP Backplane ACPC8635A TRANS-C100 ■ Ruggedized with ESD strip and EMC front SLOT A SLOT B J2 panel P1 TP1 ■ Easily integrate IPs with your software using GND RTOS VxWorks, Linux, or Win DLL for Windows® 2000/XP/Vista/7 32-bit systems. ■ Clean system cabling. ■ ■ ■ ■ Tel 248-295-0310 Fax 248-624-9234 solutions@acromag.com www.acromag.com 30765 Wixom Rd, Wixom, MI 48393 USA Bulletin #8400-312c D1 P1 P3 A B P2 P4 F1 F25 F1 F22 J1 J2 A1 A25 A1 A22 A1 A22 F1 F22 Industry Pack Carrier Cards AcPC8635A CompactPCI Carrier Cards for Industry Pack Modules ■ Power Requirements Performance Specifications Ordering Information Power +3.3V (±5%): 300mA maximum. ■ General Carrier Cards +5V (±5%): 30mA maximum. Acromag’s carrier boards provide full data access to AcPC8635A ±12V (±5%): 0mA (not used). the IP module’s I/O, ID and interrupt spaces. With full CompactPCI carrier. Holds two IP modules. Plus IP module load. access to the programmable registers, you can easily AcPC8635AE MTBF configure and control the operation of the IP modules Same as AcPC8635A with extended temperature Contact factory from the cPCI bus. range. Up to two interrupt requests are supported for each IP ■ Environmental Accessories module. All board interrupts are mapped to PCI bus Operating temperature INTA# signal. 5025-550 0 to 70°C (AcPC8635A model) Cable, unshielded, 50-pin header both ends Individual passive filters on each IP power supply line or -40 to 85°C (AcPC8635AE model). provide optimum filtering and noise isolation between 5025-551 Storage temperature the IP modules and the carrier board. Same as 5025-550 except shielded -55 to 100°C. IP Compliance (ANSI/VITA 4) 5025-552 Relative humidity Meets IP specs per ANSI/VITA 4-1995 (8MHz operation Termination panel, 50-pin connector, 50 screw 5 to 95% non-condensing. only) and IP I/O mapping to J2 per PICMG 2.4 R1.0. terminals Electrical/mechanical interface TRANS-C100 Supports single or double size IP modules. Transition module IP Module I/O space, ID space, INT, and MEM space See www.acromag.com for more information. supported. Software Development Tools Interrupts IPSW-API-VXW Supports two interrupt requests per IP module and ® VxWorks software support package interrupt acknowledge cycles via access to IP INT space. IPSW-API-WIN32 32-bit Windows® DDL driver and demo software CompactPCI bus Compliance IPSW-API-WIN64 Meets PCI spec. V2.1 and PICMG 2.0, R2.1. 64-bit Windows® DDL driver and demo software Data transfer bus IPSW-API-LINUX Slave with 32-bit, 16-bit, and 8-bit data transfer ™ Linux support (website download only) operation. 32-bit read/write accesses are implemented See www.acromag.com for more information. as two 16-bit transfers to the IPs. Interrupts P5, P6 USED ON J2 USED ON CompactPCI bus INTA# interrupt signal. Up to two ACPC8635A(E) ONLY ACPC8630A(E) ONLY requests sourced from each IP mapped to INTA#. Interrupts come from IP modules via access to IP module INT space. 32-bit memory space Upon power-up, the system auto-configuration process (plug & play) maps the carrier’s base address (for a 1K byte block of memory) into the PCI bus 32-bit memory space. ■ ■ ■ ■ Tel 248-295-0310 Fax 248-624-9234 solutions@acromag.com www.acromag.com 30765 Wixom Rd, Wixom, MI 48393 USA All trademarks are property of their respective owners. Copyright © Acromag, Inc. 2011/2012. Data subject to change without notice. Printed in USA 1/2012. P5 P6 D1 P3 P1 A B +5V F6 +12V +12V F2 +5V F5 F3 P2 P4 -12V -12V F1 F4 1 23 J3 F1 F25 F1 F22 J1 J2 A1 A25 A1 A22