PMC Carriers PMC Carriers AcPC4610CC CompactPCI Non-intelligent PMC Carrier Card (conduction-cooled) This conduction-cooled carrier card interfaces a PMC module to a CompactPCI computer system. Description This board provides an easy and low cost solution PMC and CompactPCI bus Compliance Specifications that enables use of a PMC mezzanine I/O module in a Meets PCI specification version 2.3, CompactPCI specification Environmental standard 3U CompactPCI computer system. The carrier PICMG 2.3 R1.0, and PMC specification P1386.1. Operating temperature: -40 to 85°C (conduction-cooled.) card acts simply as an adapter to route PCI bus signals Meets PCI specification version 2.3, CompactPCI specification Storage temperature: -55 to 100°C. PICMG 2.3 R1.0, and PMC specification P1386.1. to and from the PMC module through the CompactPCI Relative humidity: 5-95% non-condensing Data transfer bus: Slave with 32-bit, 16-bit, and 8-bit data card slot edge connector. All Acromag PMC modules transfer operation. American National Standard for 2mm Connector Equipment and those from other vendors are supported. Practice on Conduction Cooled Euroboards: Interrupts: CompactPCI bus INTA# interrupt signal. ANSI/VITA 30.1-2002. This board uses a PLX Technology PCI6540 transparent PCI Interface: PLX Technology PCI6540 transparent PCI/PCI PCI/PCI bridge for data transactions from the PCI bus American National Standard for Conduction Cooled PMC: bridge for data transactions from the PCI bus (system host) ANSI/VITA 20-2001(R2005). to the PMC site. The bridge device provides a 32-bit 33/66 (system host) to the PMC site. The bridge device MHz PCI interface. Power (received from the CompactPCI 3U Back Plane): provides a 32-bit 33/66 MHz PCI interface. 3.3V DC (±5%)*: 135mA typical, 150mA max. A heat frame enables conduction cooling in applications 5.0V DC (±5%)*: 50mA typical, 70mA max. Ordering Information ±12V DC (±5%)**: Per PMC module. where ambient or forced air can’t provide adequate * With no PMC module installed, ±12V DC not used. Carrier Cards cooling. This unit is ideal for airborne systems, deploy- ** Max. power 7.5W (total all supplies) per PMC standard. AcPC4610CC ment in battleground equipment, and other situations CompactPCI bus carrier card for one PMC module, MTBF: Call factory with advanced thermal management requirements. conduction-cooled Physical: CompactPCI Carrier Card Field I/O signals are routed through the carrier card’s Accessories (see accessories documentation for details) Physical configuration: 3U CompactPCI Card rear J2 connector. TRANS-C4610: Transition module, air-cooled 100 x 160mm. 5028-432: Shielded cable, SCSI-3 68-pin connector, 2m Rear CompactPCI connectors: 2mm J1 & J2 connectors. An air-cooled rear transition board, Acromag Model long. PMC connectors: Three 1mm connectors. TRANS-C4610, is available to map the field I/O on the 5025-288: Termination panel, DIN rail-mount, The conduction-cooled model (AcPC4610CC) uses a conduc- PMC module to the rear of the CompactPCI system. 68 screw terminals, SCSI-3 connector. ® tion-cooled frame with wedge-loks and thermo bars. Physical: Transition Module Features Physical configuration: Half-length 3U CompactPCI Card n 3U CompactPCI card 100 x 80mm. n Holds one PMC card Connectors: 2mm RJ2 connector which maps the rear I/O signals to a SCSI-3 connector. This model also uses a AcPC4610CC n 32-bit 33/66 MHz PCI Interface standard rear front panel assembly with a SCSI-3 connec- tor cutout. n Transparent PCI/PCI bridge for data transactions from the PCI bus to PMC module PMC 1 n Rear connection I/O access PCI Controller n Supports both 5V and 3.3V signalling n Conduction-cooled -40 to 85°C All trademarks are the property of their respective owners. Acromag, Inc. • PO Box 437, Wixom, MI 48393 • Phone: 248-295-0310 • Fax: 248-624-9234 • solutions@acromag.com • www.acromag.com 8400- 486c Printed in USA 09/09 Copyright © 2008 Acromag, Inc. Data subject to change without notice PMC Carriers J11 J14 J12 J2 J1