PMC Carriers PMC Carriers AcPC4620CC CompactPCI Non-intelligent PMC Carrier Card (conduction-cooled) This conduction-cooled carrier card interfaces two PMC modules to a CompactPCI computer system. Description This board provides an easy and low cost solution Data transfer bus: Slave with 32-bit, 16-bit, and 8-bit data Specifications that enables use of a PMC mezzanine I/O module in a transfer operation. Environmental standard 6U CompactPCI computer system. The carrier Interrupts: CompactPCI bus INTA# interrupt signal. Operating temperature: -40 to 85°C (conduction-cooled.) card acts simply as an adapter to route PCI bus signals PCI Interface: PLX Technology PCI6540 transparent PCI/PCI Storage temperature: -55 to 100°C. to and from the PMC module through the CompactPCI bridge for data transactions from the PCI bus (system host) Relative humidity: 5-95% non-condensing to the PMC site. The bridge device provides a 32-bit 33/66 card slot edge connector. All Acromag PMC modules MHz PCI interface. American National Standard for 2mm Connector Equipment and those from other vendors are supported. Practice on Conduction Cooled Euroboards: ANSI/VITA 30.1-2002. This board uses a PLX Technology PCI6540 transparent Ordering Information PCI/PCI bridge for data transactions from the PCI bus American National Standard for Conduction Cooled PMC: Carrier Cards ANSI/VITA 20-2001(R2005). (system host) to two PMC sites. The bridge device AcPC4620CC Power (received from the CompactPCI 3U Back Plane): provides a 32 or 64-bit PCI interface with 33 or 66MHz CompactPCI bus carrier card for two PMC modules, 3.3V DC (±5%)*: 135mA typical, 150mA max. bus frequencies. conduction-cooled 5.0V DC (±5%)*: 50mA typical, 70mA max. ±12V DC (±5%)**: Per PMC module. A heat frame enables conduction cooling in applications Accessories (see accessories documentation for details) * With no PMC module installed, ±12V DC not used. TRANS-C4620: Transition module where ambient or forced air can’t provide adequate ** Max. power 7.5W (total all supplies) per PMC standard. 5028-432: Shielded cable, SCSI-3 68-pin connector, 2m cooling. This unit is ideal for airborne systems, deploy- MTBF: Call factory long. ment in battleground equipment, and other situations 5025-288: Termination panel, DIN rail-mount, with advanced thermal management requirements. Physical: CompactPCI Carrier Cards 68 screw terminals, SCSI-3 connector. Physical configuration: 6U CompactPCI Card Field I/O signals are routed through the carrier card’s 233.35 x 160mm. rear J3 and J5 connectors Rear CompactPCI connectors: 2mm J1, J2, J3, J5 connectors. PMC connectors: Eight 1mm connectors. An air-cooled rear transition board, Acromag Model The conduction-cooled model (AcPC4620CC) uses a conduc- TRANS-C4620, maps the field I/O on the PMC module ® tion-cooled frame with wedge-loks and thermo bars. to the rear of the CompactPCI system. ACPC4620CC Physical: Transition Module Physical configuration: Half-length 6U CompactPCI Card Features 233.35 x 80mm. n 6U CompactPCI card Connectors: 2mm RJ2 connector which maps the rear I/O PMC 2 signals to a SCSI-3 connector. This model also uses a n Holds two PMC cards standard rear front panel assembly with a SCSI-3 connec- n 32 or 64-bit PCI Interface at 33 or 66 MHz tor cutout. n Transparent PCI/PCI bridge for data transactions PMC and CompactPCI bus Compliance Meets PCI specification version 2.3, CompactPCI specification from the PCI bus to PMC module PICMG 2.3 R1.0, and PMC specification P1386.1. n Rear connection I/O access Meets PCI specification version 2.3, CompactPCI specification PMC 1 PICMG 2.3 R1.0, and PMC specification P1386.1. n Supports both 5V and 3.3V signalling n Conduction-cooled -40 to 85°C PCI Controller All trademarks are the property of their respective owners. Acromag, Inc. • PO Box 437, Wixom, MI 48393 • Phone: 248-295-0310 • Fax: 248-624-9234 • solutions@acromag.com • www.acromag.com 8400-490c Printed in USA 09/09 Copyright © 2008 Acromag, Inc. Data subject to change without notice PMC Carriers J13 J11 J23 J21 J14 J12 J24 J22 J1 J2 J3 J5