PMC Carriers PMC Carriers AcPC4620E CompactPCI Non-intelligent PMC Carrier Card (air-cooled) This carrier card interfaces two PMC modules to a CompactPCI computer system. Description This board provides an easy and low cost solution Specifications Ordering Information that enables use of a PMC mezzanine I/O module in a Environmental standard 6U CompactPCI computer system. The carrier Carrier Cards Operating temperature: -40 to 85°C. card acts simply as an adapter to route PCI bus signals AcPC4620E Storage temperature: -55 to 100°C. CompactPCI bus carrier card for two PMC modules, to and from the PMC module through the CompactPCI air-cooled Relative humidity: 5-95% non-condensing card slot edge connector. All Acromag PMC modules Power (received from the CompactPCI 3U Back Plane): and those from other vendors are supported. Accessories (see accessories documentation for details) 3.3V DC (±5%)*: 135mA typical, 150mA max. TRANS-C4620: Transition module 5.0V DC (±5%)*: 50mA typical, 70mA max. This board uses a PLX Technology PCI6540 transparent 5028-432: Shielded cable, SCSI-3 68-pin connector, 2m ±12V DC (±5%)**: Per PMC module. PCI/PCI bridge for data transactions from the PCI bus long. * With no PMC module installed, ±12V DC not used. (system host) to two PMC sites. The bridge device 5025-288: Termination panel, DIN rail-mount, ** Max. power 7.5W (total all supplies) per PMC standard. provides a 32 or 64-bit PCI interface with 33 or 66MHz 68 screw terminals, SCSI-3 connector. MTBF: Call factory bus frequencies. Physical: CompactPCI Carrier Card Front and rear-panel access to field I/O signals are Physical configuration: 6U CompactPCI Card accommodated. The carrier card’s front panel cut-out 233.35 x 160mm. provides access to a PMC module’s front I/O connector. Rear CompactPCI connectors: 2mm J1, J2, J3, J5 connectors. Alternatively, all I/O signals can be routed through the PMC connectors: Eight 1mm connectors. ACPC4620E carrier card’s rear J3 and J5 connectors The air-cooled model (AcPC4620E) uses the standard front panel assembly with a PMC bezel cutout. An air-cooled rear transition board, Acromag Model TRANS-C4620, maps the field I/O on the PMC module Physical: Transition Module PMC 2 Physical configuration: Half-length 6U CompactPCI Card to the rear of the CompactPCI system. 233.35 x 80mm. Connectors: 2mm RJ2 connector which maps the rear I/O Features signals to a SCSI-3 connector. This model also uses a n 6U CompactPCI card standard rear front panel assembly with a SCSI-3 connec- tor cutout. n Holds two PMC cards PMC and CompactPCI bus Compliance PMC 1 n 32 or 64-bit PCI Interface at 33 or 66 MHz Meets PCI specification version 2.3, CompactPCI specification PICMG 2.3 R1.0, and PMC specification P1386.1. n Transparent PCI/PCI bridge for data transactions Meets PCI specification version 2.3, CompactPCI specification from the PCI bus to PMC module PICMG 2.3 R1.0, and PMC specification P1386.1. PCI n Rear connection I/O access Data transfer bus: Slave with 32-bit, 16-bit, and 8-bit data Controller transfer operation. n Supports both 5V and 3.3V signalling Interrupts: CompactPCI bus INTA# interrupt signal. PCI Interface: PLX Technology PCI6540 transparent PCI/PCI n -40 to 70°C bridge for data transactions from the PCI bus (system host) to the PMC site. The bridge device provides a 32-bit 33/66 MHz PCI interface. All trademarks are the property of their respective owners. Acromag, Inc. • PO Box 437, Wixom, MI 48393 • Phone: 248-295-0310 • Fax: 248-624-9234 • solutions@acromag.com • www.acromag.com 8400-490b Printed in USA 9/09 Copyright © 2008 Acromag, Inc. Data subject to change without notice PMC Carriers J13 J11 J23 J21 J14 J12 J24 J22 J1 J2 J3 J5