PMC/XMC Module Carriers APCe8675 PCI Express Carrier Card for XMC Modules J2 P5 J4 J3 POWER JTAG I/O AUX POWER SOURCE JTAG VOLTAGE (PCIe GRAPHICS) SELECT SELECT P2 P3 J1 J16 BOARD-TO-BOARD BOARD-TO-BOARD QPAIR CONNECTOR QPAIR CONNECTOR XMC REAR I/O BOARD J14 -TO- BOARD J15 SCSI-3 CONNECTOR XMC P4 REAR XMC I/O PCIe FAN P1 POWER PCIe x8 EDGE CONNECTOR One XMC mezzanine module slot ◆ Non-Intelligent carrier card ◆ PCIe x8 interface The I/O signals are accessible via rear connectors Description Key Features & Benefits and though the front mounting bracket. To Acromag’s APCe8675 carrier card interfaces an ■ One XMC module slot simplify wiring, Acromag offers cables to connect XMC mezzanine module to a PCI Express bus in ■ 8-lane PCI Express interface the carrier’s rear I/O signals to other carrier cards a PC-based desktop computer system. in adjacent slots. Cables are also available to ■ Cooling fan The APCe8675 is a PCIe bus adapter board that connect the carrier’s rear I/O to a front panel allows a PC (PCIe bus master) to control and ■ Supports high-speed serial interface between connector in an adjacent slot. communicate with the hosted XMC module. neighboring cards using protocols such as Select XMC modules from Acromag’s offering It simply acts as an adapter to route signals XAUI or Aurora of high-performance FPGA and I/O solutions between the system’s PCIe bus and the XMC ■ Routes 32 differential pairs to rear connector or use any third-party ANSI/VITA 42 compliant module connector. for LVDS I/O from the XMC module mezzanine modules. ■ JTAG programming connector supports Xilinx programmer for use in with hosted FPGA modules Aux Q Pair Connectors Power JTAG ■ Auxilliary power connection for 12V source Internal SCSI XMC XMC PCIe X8 ■ ■ ■ ■ Tel 248-295-0310 Fax 248-624-9234 solutions@acromag.com www.acromag.com 30765 Wixom Rd, Wixom, MI 48393 USA Bulletin #8400-747e PMC/XMC Module Carriers APCe8675 PCI Express Carrier Card for XMC Modules ■ Environmental Performance Specifications Ordering Information Operating temperature 0 to 70°C. ■ XMC Compliance Carrier Cards Storage temperature XMC Module APCe8675 -55 to 125°C. Complies with ANSI/VITA 42.0-2008. PCI Express carrier card for XMC modules Relative humidity 5 to 95% non-condensing. ■ I/O Interface Accessories Power The carrier provides +3.3V, +12V and -12V power to Serial Rear I/O (P2, P3) 5025-917 ® ® the XMC module. The +12V power source is jumper- Connector: Samtec QSH-DP 0.50 mm Q Pairs high Samtec Q Pairs high speed twinax cable for board-to- selectable from the PCIe bus +12V supply or the PCIe speed ground plane socket strip, differential pair. board connections. 3 inches long, 20 differential pairs. graphics power connector. The DC/DC converter Connects carrier cards in adjacent slots between P2 or These ports provide the ability to connect to left and generates a -12V supply from the +12V source. P3 connectors. High-speed serial signals originate from right neighbor carrier cards using high speed serial XMC J16 rear I/O. +3.3V (±10%): 0mA. protocols such as XAUI or Aurora. +12V (±5%): 270mA, typical with fan operating. Supports up to five transmit and five receive high Currents specified are for the carrier board only. For speed (5Gb/s) differential pairs or five LVDS pairs when the total current required from each supply, add the used with Samtec QPairs® High Speed Twinax cables. XMC module currents. Rear I/O (J1) MTBF Connector: MD68 (internal SCSI), male. Contact the factory. 32 LVDS pairs routed from the XMC P4 connector. ■ Physical 5025-913 Dimensions CS Electronics internal SCSI cable with PCI bracket- ■ PCI Express Interface Length: 12.283 inches (312.0 mm). mounted HD68 female connector. Brings the XMC J14 PCI Express interface rear I/O signals to back panel of the PC. Height: 4.200 inches (106.68 mm). 8 lane, Gen 1 capable. Width: Occupies two slots with fan installed (fan is PCIe bus compliance mounted on solder side, height is 10 mm). Occupies This device meets or exceeds all written PCI Express one slot with fan removed. specifications per revision 1.1 dated March 28, 2005. Board thickness: 0.062 inches (1.59 mm). Connectors J1: Board-to-board connection of J14 user signals. J2: Power source select jumper. J3: Auxiliary power connector (PCIe graphics). J4: JTAG I/O voltage select jumper. J14, J16 : XMC user signals (rear I/O). XMC Modules J15: XMC PCIe signals. See www.acromag.com for more information. P1: PCI Express V1.1 x8 lanes card edge. P2, P3: Board-to-board connection of J16 user signals. P4: Fan power. P5: JTAG (Xilinx programming adapter). ■ Approvals CE marked, FCC Part 15, Class A ■ ■ ■ ■ Tel 248-295-0310 Fax 248-624-9234 solutions@acromag.com www.acromag.com 30765 Wixom Rd, Wixom, MI 48393 USA All trademarks are property of their respective owners. Copyright © Acromag, Inc. 2013. Data subject to change without notice. Printed in USA 9/2013.