Industry Pack Module Carriers APCe8650 PCI Express Carrier Cards for Industry Pack Modules PCIe Graphics +12V Power Connector Field I/O IP Module A Peripheral +12V A +12V Power Connector –12V DC/DC Power Source Converter +5V Select Jumper Field I/O IP Module B B Serial FLASH +12V I P B U S Field I/O IP Module C Tx C PCIe Rx Altera Bus Level Cyclone IV Refclk Shifters FPGA Reset Field I/O IP Module D D Four Industry Pack mezzanine module slots ◆ Non-Intelligent carrier card ◆ PCIe x1 interface Description Key Features & Benefits This board interfaces standard Industry Pack (IP) ■ Four IP module slots (ANSI/VITA 4 mezzanine) mezzanine modules to a PCI Express bus on a support any combination of I/O functions PC-based computer system. ■ Board resides in memory space Four IP module slots give you the freedom to mix ■ Supports IP’s I/O, ID, INT, and MEM spaces a variety of I/O functions (A/D, D/A, digital in, APCe8650 shown with four IP modules inserted. digital out, serial I/O, etc.) on a single board. Or, ■ Plug-and-play carrier configuration and combine modules of the same type for hundreds interrupt support of channels on a single card. Either way, the ■ Two interrupt channels per IP module APCe8650 saves your precious card slots and reduces your costs. ■ Supervisory circuit reset generation Select I/O modules from Acromag’s offering of ■ Individually filtered and fused power more than forty models or use any third-party ■ Full IP module register and data access for Acromag offers more than 40 IP modules to perform ANSI/VITA 4 compliant IP modules. convenient configuration or control of the I/O analog I/O, digital I/O, serial communication, CAN bus, modules through software Mil-Std-1553, and configurable FPGA functions. ■ Non-volatile ID register to identify carrier ■ Software development tools for VxWorks, Linux, and Windows environments 50-PIN HEADERS +12V PWR +12V PWR AB CD 4-pin Aux 6-pin PCIe Peripheral Graphics IP MODULE A IP MODULE C POWER SOURCE JUMPER IP MODULE B IP MODULE D ■ ■ ■ ■ Tel 248-295-0310 Fax 248-624-9234 solutions@acromag.com www.acromag.com 30765 Wixom Rd, Wixom, MI 48393 USA Bulletin #8400-636 Industry Pack Module Carriers APCe8650 PCI Express Carrier Cards for Industry Pack Modules ■ Physical Performance Specifications Ordering Information Physical Configuration PCIe x1 lane ■ IP Module Compliance Carrier Card Length: 12.283 inches (312.0 mm) Meets or exceeds all written IP specifications per APCe8650 Height: 4.380 inches (111.25 mm) ANSI/VITA 4-1995 for 8MHz or 32MHz operation. PCI Express carrier card for Industry Pack modules Board thickness: 0.062 inches (1.59 mm) Supports Type I and Type II ID space formats. APCe8650E Max. height under IP modules: 0.110 in. (2.80 mm). Electrical/mechanical interface Same as APCe8650 plus extended temperature range Connectors Supports four single-size IP modules (A-D). A-D (carrier field I/O): 50-pin male header. Accessories IP module I/O space, ID space, INT, and MEM space Power: Auxilliary +12V power 5025-550-x supported. Flat ribbon cable, non-shielded, 50-pin connector at ■ Environmental IP module I/O space both ends. Specify x = length, in feet (12ft. max.) Operating temperature 16 and 8-bit; supports 128 byte values per IP module. 5025-551-x 0 to 70°C (APCe8650) IP module ID space Flat ribbon cable, shielded, 50-pin connector at both or -40 to 85°C (APCe8650E model). 16 and 8-bit; Supports Type I 32 bytes per IP ends. Specify x = length, in feet (12ft. max.) Storage temperature (consecutive even byte addresses) and Type II 32 words 5025-552 -55 to 100°C. per IP via D16 data transfers. Termination panel, DIN rail-mount, 50 screw terminals, Relative humidity IP module memory space 50-pin ribbon cable connector 5 to 95% non-condensing. 16 and 8-bit; supports up to 8M bytes of memory space per IP module. Power Industry Pack Modules +3.3 Volts (±10%): 190mA, typical; 220mA max. Interrupts See www.acromag.com for more information. +12 Volts (±5%): 130mA, typical; 150mA max. Supports two interrupt requests per IP and interrupt acknowledge cycles via access to IP INT space. Software Development Tools All IP module power is derived from the +12V power supply. +5V, +12V, and –12V are supplied to IP See www.acromag.com for more information. PCI Express Bus Compliance modules. The +12V power can be supplied from the IPSW-API-VXW This device meets or exceeds all written PCI local bus PCIe bus or optionally from either of two auxiliary ® VxWorks software support package specifications per rev. 1.1 dated March 28, 2005. power connectors. IPSW-API-WIN32 System base address MTBF ® 32-bit Windows DLL driver software support package This board operates in PCI memory space. It requires Contact the factory. IPSW-API-WIN64 256 bytes for mapping the PCI configuration registers ® 64-bit Windows DLL driver software support package and 64M bytes for IP module ID, IO, INT and memory space. IPSW-LINUX ® Linux support (website download only) Data transfer bus Slave with 32, 16, and 8-bit data transfer operation. 32-bit read or write accesses implemented as two 16-bit transfers to IP modules. Interrupts (PCI bus INTA# interrupt signal) Up to two requests sourced from each IP mapped to INTA#. Interrupt vectors come from IP modules via access to IP module INT space. ■ ■ ■ ■ Tel 248-295-0310 Fax 248-624-9234 solutions@acromag.com www.acromag.com 30765 Wixom Rd, Wixom, MI 48393 USA All trademarks are property of their respective owners. Copyright © Acromag, Inc. 2011. Data subject to change without notice. Printed in USA 5/2011.