ACEK 3354-7P - NEXCOM

Description

SMARC Starter-Kit, TI SitaraTM AM3354, ARM® Cortex™ A8 Bootable SD, DDR3 512MB, eMMC 4GB on ACES 3354 Integrated ACEB-35 with 7" LVDS/ WVGA, 7" Capacitive Touch
NEXCOM ACEK 3354-7P is an SMARC Starter Kit based-on ARM® Cortex™ A8 processor onto ACES 3354 that plugged in ACEB-35 carrier board with 7" LVDS LCD, 7" capacitive touch and integrated an AC/ DC 36W power adaptor by DC + 12V input. This starter-kit is assembly for engineer to develop their ARM-based industrial/ embedded device or equipment.

Part Number

ACEK 3354-7P

Price

Request Quote

Manufacturer

NEXCOM

Lead Time

Request Quote

Category

Embedded Computers » sARM/SoC Solutions

Specifications

Form factor

ACES 3354: SMARC STD 1.0 compliance with 314pins connector, 82 x 50mm
ACEB-35: SMARC STD 1.0 compliance with 314pins socket, 146 x 105 x 16mm (height)
ACEK 3354-7P: Bakelite Tabletop Box, 260 x 135 x 60mm (height)

Processor

Build-in Texas Instruments AM3354 ZCZ 324-pin PBGA, Cortex™ A8 up to 720MHz

Power Management IC

PMIC TPS65910A3 integrated w/ 4 DC/DCs, 8 LDOs and RTC in 6 x 6mm QFN

System Memory

SDRAM: DDR3 512MB
Flash: eMMC 4GB (compliant eMMC 4.41)
SPI Flash: 8Mbit

Display

Graphic Accelerator: SGX530 2D/ 3D Accelerator
- Industry-Standard API support: Direct3D Mobile, OpenGL ES1.1 and 2.0, OpenVG 1.0.1- Support (USSE) Universal Scalable Shader Engine
Display Interfaces- LVDS: Default 800 x 480 (24bit) for 7" LCD/ LVDS- TTL: Reserved design interface for resolution up to 1024 x 768@60Hz
7" LVDS Display: 7" WVGA (800 x 480) default LCD for ACEK 3354-7P starter-kit- LED backlight
7" Touch: 7" Projected Capacitive Touch Panel- Default single point touch for Windows Compact 7.0- Optional multi touch up to 5 x points

Connectivity

Network: 1 x Gigabit Ethernet by RJ45
USB#0: Onboard USB Hub GENESYS: GL850G for 2 x USB 2.0 Host
USB#1: USB-OTG by Mini AB type connector
SDIO: up to 2 x MMC/ SD
UART4: (TX, RX, CTS#, RTS#) 1 x for Debug
UART5: DB9, RS232/ RS422/ RS485 pre-selected by SW2- 16C750 compatibility- Auto-baud between 1200 bps and 115.2 Kbps
SPI: One Serial Peripheral Interface (SPI) interfaces
I2C: Two Inter-Integrated Circuit interfaces
General Purpose I/O: Programmable 8 x GPIO signals on JP4 10-pins header
DCAN: Dual CAN interfaces support bitrates up to 1 Mbit/s CAN 2.0B protocol (ISO 11898-1)- Logic level signals from Module based CAN bus protocol controllers RXD, TXD only- Two Module GPIOs reserved for optional use as CAN bus error status
Audio Code: TLV320AIC3101
Speaker-out: 1W/ch. Into 8Ω at 5V
Watchdog Timer interface

System Environment

Power Input: DC 5V +/- 5% (supply by ULP-COM/ MXM3.0 interface)
Power Consumption: DC + 5V/ 0.4A typical 2.0W to 3.2W during active operation
Dimensions: 10
Environment- Operating temperatures: 0°C to 40°C- Storage temperature: -20°C to 85°C- Relative humidity: 10% to 90%, (Non-condensing)
Certifications: Meet CE/ FCC class A

BSP Support

The Board Support Package for Windows Compact 7.0 includes some different levels software- MLO: CPU loader- EBOOT: Bootloader- NK: Windows Compact 7.0 OS IMAGE

Categorization Information

IoT Automation Solutions
Embedded Computing
ARM/SoC Solution

Features

SMARC STD 1.0 compliant ARM® Cortex™ A8 Starter-Kit
TI- AM3354, ARM® Cortex™ A8 720MHz, build-in SGX530 Graphic Accelerator
Onboard 512MB DDR3, 4GB eMMC and bootable SD on the carrier board
Support GbE, USB, USB-OTG, 2UART, Audio, DCAN, I2S, 3x I2C and 8 x GPIO
Build-in 7" LVDS LCD, WVGA with 7" capacitive Touch
Integrated AC/ DC adapter for DC + 12V @ 3A input
BSP ready to support Windows Compact 7.0

Datasheet

fe6b9ef9-61c6-44d1-bada-20965a66f675.pdf

374 KiB

Download

Extracted Text

® SMARC Starter-Kit, TI SitaraTM AM3354, ARM Cortex™ A8 Bootable SD, DDR3 512MB, eMMC 4GB on ACES 3354 ACEK 3354-7P Integrated ACEB-35 with 7” LVDS/ WVGA, 7” Capacitive Touch Main Features ® Support GbE, USB, USB-OTG, 2UART, Audio, DCAN, I2S, 3x I2C and SMARC STD 1.0 compliant ARM Cortex™ A8 Starter-Kit ® 8 x GPIO TI- AM3354, ARM Cortex™ A8 720MHz, build-in SGX530 Graphic Build-in 7” LVDS LCD, WVGA with 7” capacitive Touch Accelerator Integrated AC/ DC adapter for DC + 12V @ 3A input Onboard 512MB DDR3, 4GB eMMC and bootable SD on the carrier board BSP ready to support Windows Compact 7.0 Product Overview ® NEXCOM ACEK 3354-7P is an SMARC Starter Kit based-on ARM Cortex™ A8 processor onto ACES 3354 that plugged in ACEB-35 carrier board with 7” LVDS LCD, 7” capacitive touch and integrated an AC/ DC 36W power adaptor by DC + 12V input. This starter-kit is assembly for engineer to develop their ARM-based industrial/ embedded device or equipment. ® The ACES 3354 SMARC module embedded Texas Instruments Sitara AM3354 ARM Cortex™ A8 processor features low power and high performance graphic-accelerated by SGX530 core to support industrial API standard Direct3D Mobile, OpenGL ES1.1 and 2.0, OpenVG 1.0.1. The ACES 3354 build-in system memory with 512MB DDR3 and SPI flash with bootable 4GB eMMC by SDIO interface. The ACES 3354 support 24-bit LVDS or TTL LCD screen resolution up to 1366 x 768, offering either capacitive or resistive touch. The ACEK 3354-7P works as application BSP-ready for Windows Embedded Compact 7.0 at the first stage evaluation and future development plan for Linux Kernel 3.2.x and Android 4.2.x. NEXCOM provide embedded software customization service to enable customer new project rapidly deploy an operating system and fully utilize the features of the underlying hardware platform that may configure to support the desired peripherals, operating system. NEXCOM share the same pin-out standard of SMARC, the developers can easily migrate to a higher or lower-end SMARC from customization to full ODM board design. ACES 3354 SMARC is the ideal ARM-based solution platform for Human Machine Interfaces, Industrial Automation, Industrial control, Remote monitoring devices. Embedded system applications like Connected Vending Machines, Weighing Scales, Consumer Medical Appliances, Educational Consoles and Smart Toll System. Specifications Form factor System Memory ACES 3354 : SMARC STD 1.0 compliance with 314pins connector, 82 SDRAM : DDR3 512MB x 50mm Flash : eMMC 4GB (compliant eMMC 4.41) ACEB-35 : SMARC STD 1.0 compliance with 314pins socket, SPI Flash : 8Mbit 146 x 105 x 16mm (height) Display ACEK 3354-7P : Bakelite Tabletop Box, 260 x 135 x 60mm (height) Graphic Accelerator : SGX530 2D/ 3D Accelerator Processor - Industry-Standard API support : Direct3D Mobile, OpenGL ES1.1 and Build-in Texas Instruments AM3354 ZCZ 324-pin PBGA, Cortex™ A8 2.0, OpenVG 1.0.1 up to 720MHz - Support (USSE) Universal Scalable Shader Engine Display Interfaces Power Management IC - LVDS : Default 800 x 480 (24bit) for 7” LCD/ LVDS PMIC TPS65910A3 integrated w/4 DC/DCs, 8 LDOs and RTC in -TTL : Reserved design interface for resolution up to 1024 x 768@60Hz 6 x 6mm QFN 7” LVDS Display : 7” WVGA (800 x 480) default LCD for Embedded ARM www.nexcom.com Dimension Drawing Block Diagram of ACEB-35/ ULP-COM Carrier Board (146 x 105mm) Block Diagram of ACES 3354/ ULP-COM Module (82 x 50mm) DDR3 303MHz 24 bits TTL RGB CH7026 512MB/1GB LINE-OUT I2C0 I2S RGMII2 MDI MDI 3PIN JSTx2 AIC3106 RJ-45 DB-15 Giga LAN PMIC MIC-IN PWR 24bit TTL LVDS TTL -> LVDS SDIO0(4bits) 18 bit LVDS LVDS SPI SPI0(CS0) SD Socket CONNECTOR 8MbFLASH 24 bits TTL HUBUSB1 SPI0 (CS1) 24 bits TTL TOUCH 24 bits TTL USB1 USB HUB HUBUSB2 CONNECTOR CONTROL AM335X ULP-COM USB0 (For OTG) 324 Pin 314 Pin ULP-COM GPIOx10 USB I2C x 3 HUBUSB1 PIN HEADER 314 Pin CONNECTOR I2S(For Audio) SDIO ( 4 bits ) HUBUSB2 MINIPCIE DCANx2 SPI0 (CS1) 3PIN JSTx2 CONNECTOR GPIO x 10 CAN BUS x2 MINIUSB UART5 USB0 UART5(TX,RX,CTS,RTS) DB-9 CONNECTOR UART0 ( For Debug) 4Pin JSTx1 SDIO1 I2C UART4 6Pin JSTx1 JST 3Pin (For Touch) eMMC 4GB ACEK 3354-7P starter-kit System Environment - LED backlight Power Input: DC 5V +/- 5% ( supply by ULP-COM/ MXM3.0 interface) 7” Touch : 7” Projected Capacitive Touch Panel Power Consumption : DC + 5V/ 0.4A typical 2.0W to 3.2W during active - Default single point touch for Windows Compact 7.0 operation - Optional multi touch up to 5 x points Dimensions: 10 Environment Connectivity - Operating temperatures : 0°C to 40°C Network : 1 x Gigabit Ethernet by RJ45 - Storage temperature : -20°C to 85°C USB#0 : Onboard USB Hub GENESYS: GL850G for 2 x USB 2.0 Host - Relative humidity : 10% to 90%, (Non-condensing) USB#1 : USB-OTG by Mini AB type connector Certifications : Meet CE/ FCC class A SDIO : up to 2 x MMC/ SD UART4 : (TX, RX, CTS#, RTS#) 1 x for Debug BSP Support UART5 : DB9, RS232/ RS422/ RS485 pre-selected by SW2 The Board Support Package for Windows Compact 7.0 includes some - 16C750 compatibility different levels software - Auto-baud between 1200 bps and 115.2 Kbps - MLO : CPU loader SPI : One Serial Peripheral Interface (SPI) interfaces - EBOOT : Bootloader I2C : Two Inter-Integrated Circuit interfaces - NK : Windows Compact 7.0 OS IMAGE General Purpose I/O : Programmable 8 x GPIO signals on JP4 10-pins header DCAN: Dual CAN interfaces support bitrates up to 1 Mbit/s CAN 2.0B Ordering Information protocol (ISO 11898-1) ACES3354 (P/N : ULP-COM module are subject to request) - Logic level signals from Module based CAN bus protocol controllers SMARC module AM3354 Cortex™ A8 720MHz, 512MB DDR3, RXD, TXD only 4GB eMMC, GbE, USB, USB-OTG, 82 x 50mm - Two Module GPIOs reserved for optional use as CAN bus error status Audio Code : TLV320AIC3101 ACEB-35 (P/N : ULP-COM module are subject to request) Speaker-out : 1W/ch. Into 8Ω at 5V SMARCCarrier Board 146 x 105mm with MXM3.0/ 314 pins socket, GbE, Watchdog Timer interface USB, USB-OTG, COM, VGA/ LVDS/ TTL, MIC-in/ Speaker-out, DCAN, I2C, DC Jack +12V input Boot Source SPI Flash from ACES 3354 ACEK3354-7P (P/N : ULP-COM module are subject to request) eMMC Flash from ACES 3354 ® SMARC ARM Cortex™ A8 Starter-Kit integrated ACES 3354 onto ACEB- SD Card from carrier ACEB-35 35 carrier board with 7” LVDS LCD and 7” capacitive touch with AC/ SC Card : WinCE 7 DC+12V power adapter AC110/ 240V input eMMC : Linux Embedded ARM We reserve the right to change specifications and product descriptions at any time without prior notice. Last update: 02/26/2014

Frequently asked questions

IPC Station' parent company, GID Industrial, specializes in procuring industrial parts. We have years of experience finding rare and obsolete equipment that our customers need in order to get back to business. There are other companies who claim to do what we do, but we're confident that our commitment to quality and value is unparalleled in our field.

The warranty we offer will be based on what we negotiate with our suppliers. It is possible for some parts to be sold as-is and without a warranty. Our specialty, single board computers, tend to receive a one-year warranty.

We use FedEx, UPS, DHL, and USPS. We have our own accounts, but we can also use yours if you would prefer. However, we can use other carriers if it will be more convenient for you.

IPC Station will definitely serve you. In fact, much of our business is international, and we are familiar with shipping to destinations all across the globe.

Visa, MasterCard, Discover, and American Express are all accepted by IPC Station. We can also accept wire transfers and PayPal, or a check if you're in the USA. Terms may available for larger orders, upon approval.

What they say about us

FANTASTIC RESOURCE

One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!

Bucher Emhart Glass

EXCELLENT SERVICE

With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.

Fuji

HARD TO FIND A BETTER PROVIDER

Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.

Applied Materials

CONSISTENTLY DELIVERS QUALITY SOLUTIONS

Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.

Nidec Vamco

TERRIFIC RESOURCE

This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.

Trican Well Service

GO TO SOURCE

When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.

ConAgra Foods

Why buy from GID?

What they say about us

Related Products