rBOX630 Robust RISC-based DIN-rail Fanless Embedded System with i.MX 6 Processor, 4 COM, 2 CAN Bus and DIO Features 3 Antenna hole ● Fanless design 2 LAN (for 3G/GPRS/Wi-Fi) ● RISC-based module (i.MX 6) processor 1 HDMI ● 1GB DDR3 SDRAM onboard (Support screw lock) ● 4GB eMMC onboard ● Completed industrial AP development software 4 COM ● 12~48 VDC wide range power input with terminal block ● Ready-to-run embedded Linux operating system ● Wide operating temperature range from -40°C to +70°C 2 CAN Bus Front view 1 Console port 1 Power DC-in SD/SIM Card Socket Fanless Low Power DIN-rail kit Freescale i.MX 6 EN60950 Isolation Ext. Temp IP30 1 DIO (8 IN/ 8 OUT) 1 OTG USB Rear view Introduction Easy-to-access interface System I/O Outlet HDMI 1 x HDMI (Support screw lock) The rBOX630 cost-effective DIN-rail fanless embedded system utilizes the low power USB 1 x USB 2.0 OTG RISC-based module (i.MX 6) processor and is designed to withstand temperatures ranging from -40°C to +70°C for using in harsh environment and industrial automation CAN 2 CAN 2.0 B (Phoenix connector, applications. non-isolation) Meets ISO 11898 standard The rBOX630 features 4 RS-232/422/485 serial ports, dual LANs, 8 digital input channels, Software control termination resistor 8 digital output channels, 2 CAN bus and 1 eMMC onboard 4 GB & 1 x SDHC socket 120 ohm can high speed up to 1Mbit/s for storage expansion (easy to access) in a compact, IP30 protected, industrial-strength for transmit/receive robust case. Two power paths input minimize the risk of data loss in the event of a DIO 1 x DIO ( 8 IN/ 8 OUT ) with Isolation 2KV single power failure. Its vertical DIN-rail form factor makes it easy to install the system DI: Wet/Dry in a small cabinet. Because of ARM's low power consumption architecture, rBOX630 DO: Wet generate little heat while being operated. The ready-to-run rBOX630 is specially designed DI: for industrial machine, automatic parking lot, traffic cabinet and more. Input channels: 8, source type Input voltage: 0 to 30 VDC digital input Hardware Specifications levels for dry contacts: -Logic level 0: close to GND Standard Color Sliver-Black -Logic level 1: open Construction Extruded aluminum and heavy-duty steel, IP30 Digital input levels for wet contacts : CPU i.MX 6, Cortex-A9 RISC CPU, 800MHz -Logic level 0: +10V to +24V (DI to COM-) System Board Q7M120 -Logic level 1: +3V max. System Memory 1 x DDR3-1600 onboard, 1GB DO : Output channels: 8, sink type System I/O Outlet Serial Port 4 x RS-232/422/485 (COM 1 ~ 4) Output current: Max. 200 mA per COM 1~4 with TX/RX/RTS/CTS signals channel RS-232/422/485 interface select by On-state voltage: 24 VDC nominal, open software collector to 30 V LAN 1 x 10/100/1000 Mbps Ethernet Optical isolation protection 2 KV 1 x 10/100 Mbps Ethernet Console Port DB9 connector Magnetic isolation protection 1.5KV For user setting with debug RTC Battery onboard Provides power for the internal real time clock & calendar Ideal for vibration environment & reduces maintenance efforts Alarm Contact One relay output with current 0.5A@30VDC 367 * All specifications and photos are subject to change without notice. DIN-rail Embedded Systems Hardware Specifications Ordering Information System I/O Outlet Wireless 1 x Mini card socket (supports USB Standard interface) with 1 x SIM Socket by outside rBOX630-FL-DC Robust DIN-rail fanless embedded system with Q7-RISC access and is easy plug/pull. module (i.MX 6), 4 COM, 2 CAN and DIO 1 x Mini card socket (supports USB&PCIE (-40°C ~ +70°C) interface) with 1 x SIM Socket by inside Watchdog Timer WDT 1: one step is 1 sec, 255 levels Optional LEDs System Power, Alarm, Ready/Active, COM Wall mount kit (TX, RX), Wireless Wireless (3G/GPS or Wi-Fi) module Alarm DC PWR1 or PWR2 Storage 1 x eMMC 4 GB onboard (for boot disk) Supports 1 x SDHC Card (easy-to-access, for store only.) Installation DIN-rail, wall mount Power Supply Power Input 2 power paths with terminal block Power Input Range 12-48 VDC Power Input Rating 12-48 VDC, 0.74-0.23A 0 Power Protection DC Version: OVP (Over voltage protection) UVP (Under voltage protection) Reverse protection 1 Operating Temperature -40°C ~ +70°C (-40°F ~ +158°F) Humidity 10% ~ 95% Vibration Endurance 5G @ 10-150Hz, amplitude 0.35ms Weight (net/gross) 0.9 kg (2 lb)/1.3kg (2.87 lb) 2 Dimensions 55 mm (2.16") (W) x 155 mm (6.10") (D) x 110 mm (4.33") (H) OS Linux Linux Host OS/ Development OS : Ubuntu 12.04 Yocto Dora LTS Toolchain/ Cross compiler : Freescale Yocto 3 Kernel : 3.0.35 (with Freescale and Axiomtek hardware modified patch) Certificate FCC Part 18 Heavy Industrial CE 4 5 6 Dimensions 7 8 9 10 11 axiomtek.com 368 * All specifications and photos are subject to change without notice. © 2017 Axiomtek Co., Ltd. All rights reserved.