AMAX-1220 Open Frame Type 2/ 4-axis AMONet AMAX-1240 Motion Slave Modules Features ƒ End limit logic is switchable (high or low active) ƒ BoardID is switchable ƒ Easily visible LED indicators on board to do diagnosis ƒ Direct wire to servo drive to save terminal board space while installation ƒ Max. 6.5 MHz, 4-axis pulse output ƒ 28 bits counter for incremental encoder ƒ Horizontal installation for for servo or stepping motor driver ƒ Suitable for DIN-rail mounting AMAX-1220 AMAX-1240 RoHS COMPLIANT 2002/95/EC Introduction AMAX-1220 and AMAX-1240 have compact open frame designs for horizontal placement and an interface connector mounted on the board. With a transfer cable to servo drive, both models can conveniently connect to Mitsubishi J3, Yaskwa Sigma V and Panasonic A4/A5. The AMAX-1220 is an economic 2-axis AMONet slave module which supports motion functionality in point-to-point (PTP), linear & circular interpolation, simultaneously start/ stop among multiple slave modules, and brake signal to servo for emergence consideration. The AMAX-1240 is an advanced 4-axis AMONet slave module which not only supports AMAX-1220 motion functionality, but also supports advanced features in position compare and triggering function. Both linear interval and table setups are supported. Specifications General Pulse Type Motion Control ƒ Bus Type AMONet RS-485 ƒ Motor Driver Support Pulse-type servo ƒ Certification CE, FCC Class A ƒ Number of Axes AMAX-1220: 2 AMAX-1240: 4 ƒ Connectors RJ-45 x 2 are for communication port DB-26 connector by transfer cable to servo ƒ Interpolation Linear and circular drives. Other are screw terminal type connectors ƒ Max. Output Speed 6.5 Mpps ƒ Dimensions (L x W x H) 141 x 108 x 60 mm (5.6" x 4.3" x 2.4") ƒ Step Count Range ±134, 217, 728 ƒ System Power 2 W @ 24 V typical ƒ Pulse Output Type OUT/DIR, CW/CCW, A/B phase Consumption ƒ Position Counter ±134, 217, 728 Output Channel Power ƒ Home Modes 13 Consumption 120W typical, 240W max. ƒ Velocity Profiles T-Curve, S-Curve Input Channel Power ƒ Local I/O Consumption AMAX-1220: 8 W @ 24 V external power (max.) Machine Interfaces: EL+/-, ORG and SD (Slow Down) for Each Axis AMAX-1240: 10 W @ 24 V external power (max.) Servo Driver Interfaces: ALM, RDY, SVON, INP, Break for Each Axis ƒ System Power Input 24 VDC within 200 mV ripple Position Compare I/O: LTC, CMP for Each Axis(Only available for ƒ Humidity 5 ~ 95% RH, non-condensing (IEC 60068-2-3) AMAX-1240-AE) ƒ Operating Temperature 0 ~ 60°C (32 ~ 140°F) Simultaneous Move Within Multiple Modules: CSTA/CSTP (Simultaneously Start/Stop) for Ordering Information each model General Purpose I/O: AMAX-1220 supports 8xDI and 8xDO ƒ AMAX-1220-AE Economic 2-axis AMONet Motion Control Module ƒ AMAX-1240-AE Advanced 4-axis AMONet Motion Control Module Encoder Interface ƒ Input Type A/B phase, CW/CCW Accessories ƒ Counts per Enc. Cycle x1, x2, x4 (AB phase only) ƒ PCL-10153PA5-2E 50-pin Cable to Panasonic A4/A5 Servo, 2 m ƒ Input Range Low: 0 ~ 0.5V ƒ PCL-10153PA5LS-2E 50-pin Cable to Panasonic MINAS A Servo, 2 m High: 3.5 ~ 7V ƒ PCL-10153YS5-2E 50-pin Cable to Yaskawa Sigma V/7 Servo, 2 m ƒ Isolation Protection 2,500 V RMS ƒ PCL-10153MJ3-2E 50-pin Cable to Mitsubishi J3/J4 Servo, 2 m ƒ Max. Input Frequency 2 MHz @ 5 V ƒ PCL-10153DA2-2E 50-pin Cable to Delta A2 Servo, 2 m Online Download www.advantech.com/products All product specifications are subject to change without notice Last updated : 27-Jul-2016